Installing windows your pc will restart several times sit back and relax

Проблемы с ноутбуком

На ноутбуке появилось сообщение об ошибке
Windows Boot Manager
Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
1. Insert your windows installation disc and restart your computer.
2. Choose your language settings, and then click »Next.»
3. Click »Repair your computer.»
If you do not have this disc, contact your system administrator or computer manufacturer for assistance.
File: \Boot\BCD
Status: 0xc000000f
Info: An error occurred while attempting to read the boot configuration data.

Или в переводе на русский
Диспетчер загрузки Windows
ОС Windows не удалось запустить. Последние аппаратные или программные изменения могут быть причиной. Для решения этой проблемы:
1. Вставьте установочный диск Windows, и перезагрузите компьютер.
2. Выберите параметры языка, а затем нажмите кнопку» Далее. »
3. Нажмите» ремонтом вашего компьютера. »
Если у вас нет этого диска, обратитесь к системному администратору или изготовителю компьютера для получения помощи.
Файл: \ Boot \ BCD
Статус: 0xc000000f
Информация: Произошла ошибка при попытке чтения данных конфигурации загрузки.

Нашла установочный диск Windows 7. Безрезультатно.
А вот установочный диск Windows 8 помог. Хотя и установлен на ноутбуке был Windows 7.

• Перезагрузила компьютер.
• Зашла в BIOS при помощи специальной клавиши, которая для каждой материнской платы своя, у меня F2.
• Открыла раздел биоса Main. Установила F12 Boot Menu Enabled. Далее нажала F10 для сохранения изменений меню и выхода из него.
• Установила установочный диск в CD ROM, который сделала первым в загрузочной иерархии. По умолчанию загрузка производится из жесткого диска.
• Перезагрузила компьютер и нажала F12 для входа в Boot Menu.
• При появлении на экране строки «Press any kay from CD or DVD» нажала любую из клавиш, чтобы запустилась загрузка с CD ROM и началась установка Windows.
• После того, как появится меню установки нажимаем «Далее».
• Теперь необходимо в левом нижнем углу найти «Восстановление».

После нажатия на поле » Восстановить» у меня появилась строка Диск заблокирован. По этой причине пришлось все предыдущие операции проделать повторно и отправится в меню «Диагностика» и «Дополнительные параметры» там «Командная строка».
Теперь займемся открытием доступа к диску, на котором находится Windows.

Необходимо прописать простую команду «Bootrec /fixmbr». Нажимаем «Enter».

• Ключ меняем на «/rebuildbcd». Опять же подтверждаем «Enter».
• Перезагружаем компьютер.
• Теперь появляется доступ к диску.
  Главное, что для процедуры необходимо использовать дистрибутив Windows. И даже может понадобиться ключ активации, с помощью которого ранее и была установлена текущая система. В противном случае команда может не сработать, а значит все останется, как есть.
  У меня на удивление сработало при запуске диска с Windows 8, и система с Windows 7 восстановилась.

В моем случае думаю что все проблемы связаны с тем, что первоначально на ноут буке была установлена Windows Vista. Возможно аппаратно мой ACER не тянет Windows 7 и поэтому у меня частенько происходит перезагрузка или загорается синий экран.

Источник

FIX: Computer constantly restarts after installing Windows

• Windows 10 restarting constantly is more than annoying because it renders your PC useless.
• Users reported this problem after installing Windows and many of them blame the antivirus.
• For any information about the most popular OS, explore our Windows 10 section.
• Use our Tech Troubleshooting Hub for help with any PC problems.

Although Windows 10 offers a lot of cool, new features, it can still bring some problems, as well.

In this article, we’re going to show you what to do if the fresh installation of Windows 10 forces your computer to reboot constantly.

What can I do if the PC reboots after installing Windows 10?

Here are a few other problems that users are facing and can be solved using our guide:

• Windows 10 continuous, endless reboot – Sometimes their PC can get stuck in an endless reboot. Try some of our solutions.
• Windows 10 reboot loop – Usually caused by a problematic update, and to fix it, you need to find and remove that update.
• Windows 10 reboot randomly – C an be caused by hardware problems, so be sure to inspect your hardware.
• Windows 10 install reboot loop – This is a common problem that can be fixed by installing Windows 10 again.

1. Check your antivirus

According to users, sometimes your antivirus can cause this problem, especially if it’s not fully compatible with Windows 10.

Many users reported that this problem occurred with Avast antivirus, but after removing it, the issue was resolved completely.

Keep in mind that you might not be able to access Windows 10 normally due to this problem, so you might have to use Safe Mode to remove Avast.

Once you enter Safe Mode, be sure to uninstall Avast or the antivirus that you’re using and check if that solves the problem.

Keep in mind that antivirus tools might leave behind certain files and registry entries that can cause the problem to reappear.

To completely remove an antivirus, it’s recommended to use a dedicated removal tool. Most antivirus companies offer dedicated removal tools for their software, so be sure to download one for your antivirus.

Once you completely remove your antivirus, check if the problem is resolved. If your antivirus was the problem, you might want to consider switching to a different antivirus solution.

We strongly recommend VIPRE Antivirus Plus because it’s light on your system but it offers great protection for a reasonable price.

This excellent solution features web filtering, advanced active protection and it updates its definitions automatically.

Potentially harmful files will be moved into a quarantined environment so you can review them after the scanning process.

VIPRE Antivirus Plus

2. Prevent your PC from rebooting

1. Boot your computer in Safe Mode.
2. Go to Search, type sysdm.cpl, and open it from the results.
   
3. Click the Advanced tab, and then click the Settings button under Startup and Recovery.
   
   
4. Uncheck Automatically restart option, then click OK and reboot your computer.
   

Note: This probably won’t solve your problem but it will provide you with more information. Next time your computer restarts, you’ll probably get a BSoD.

You can use the message or the error code you get from the blue screen to search it on our large collection of BSoD solutions.

3. Fix the Master Boot Record

1. Restart your PC several times during the boot sequence until a list of options appears.
2. Select Troubleshoot, then Advanced options, and selectCommand Prompt.
3. Run the following commands:

bootrec /FixMbr

bootrec /FixBoot

bootrec /ScanOs

bootrec /RebuildBcd

4. Run the chkdsk command

1. Restart your PC several times during the boot sequence and start Command Prompt as shown in the previous solution.
2. Enter chkdsk /r X: (replace X with the letter that matches your systempartition and keep in mind that letters might be changed if you start Command Prompt outside of Windows)
   
3. Keep in mind that this process can take 20 minutes or more, depending on the size of your drive.

5. Roll back to a previous build

1. Restart your PC during the boot phase few times until the list of options appears.
2. Choose Troubleshoot, then go to Advanced options, select See more recovery options, and choose Go back to the previous build.
3. Select your user account and enter your password.
4. Click the Go back to the previous build button and follow the instructions on the screen.

Note: Once your PC is restored to the previous build, the problem should be resolved. If you can’t find this setting, you can also use System Restore to go back to the previous build.

If an update caused this problem, you might want to prevent this update from installing. To see how to do that, check out our how to prevent Windows from installing automatic updates article.

6. Check your hardware

Sometimes your hardware can cause this problem to appear, and in order to fix it, you need to disconnect all USB devices from your PC and check if the problem still appears.

Several users claim that the issue was their Wi-Fi adapter, so you might want to try removing it to solve this problem.

In a few instances, users reported that their CPU was the cause, but before you replace any major hardware component, be sure to perform a detailed inspection of your hardware.

7. Check your startup applications

1. Start Windows 10 in Safe Mode.
2. Press the Windows Key + R and enter services.msc, then click OK or press Enter.
   
3. Navigate to Services tab, check Hide all Microsoft services and click on Disable all.
   
4. Go to the Startup tab and click on Open Task Manager.
   
5. S elect the first item on the list, right-click it, and choose Disable from the menu. Repeat this step for all the startup applications.
   
6. Close Task Manager, go to the System Configuration window and click Apply and OK to save the changes.
   
7. Restart your PC.

Note: If the problem doesn’t appear anymore, you need to enable disabled startup applications and services one by one or in groups until you find the way that is causing the problem.

Once you find the problematic application, you can remove it or update it and check if that solves the issue.

We hope that some of these solutions helped you to solve the restarting problem, if you have any suggestions or comments, please reach for the comments section below.

Editor’s Note: This post was originally published in March 2018 and has been since revamped and updated in October 2020 for freshness, accuracy, and comprehensiveness.

Источник

Your PC will restart several times during updates [Full Fix]

• If your PC won’t restart several times during updates as indicated by the Windows message, it’s possible that the process is incomplete.
• But don’t worry, there are several ways to fix this and we elaborate on the solutions below.
• Want to be prepared for similar situations? Read more in our Windows Updates Errors collection of articles.
• You can find the complete library in our Windows Troubleshooting Hub.

Some Windows 10 users experienced this problem after downloading and installing Windows updates.

Namely, when the update is almost complete, the screen shows the familiar Windows loading animation with a notification that Working on updates 99%; Don’t turn off your PC. This will take a while, and Your PC will restart several times at the bottom of the screen.

However, nothing happens and the PC keeps displaying this message.

This problem could be as a result of corrupt directories, malware infection, and incomplete updates.

If you are wondering how to fix the Your PC will restart several times issue, his guide puts you through 7 solutions to resolve it.

How to fix Your PC will restart several times error?

1. Scan your device with an antivirus

Malware can infect your PC registry leading to the above-mentioned problem. Hence, we recommend using a powerful third-party antivirus such as BullGuard to perform an in-depth scan.

So, if the updating process fails to complete, restart your device and install this antivirus tool.

BullGuard Antivirus

The tool provides a triple-layer, real-time protection, plus scanning signatures for all kinds of anomalies associated with malware. Any detected malware is quarantined and then neutralized before the infection can even begin.

Here’s how to scan the system for malicious software using BullGuard:

1. Download the product for free using the link above. The installation process is quick and easy.
2. After the initial configuration steps, allow the tool to optimize your PC.
3. Then, go to the Antivirus module, click on the options, and select Quick Scan or Full Scan. The former will scan only the most important elements of your device, while the latter will perform an in-depth scan that can last more than an hour.
4. Restart the PC afterward.

If the error persists, you should move to the next steps.

2. Run an SFC scan

1. Go to Start, type cmd, then right-click on Command Prompt and select Run as Administrator.
2. Now, type the sfc /scannow command.
3. Wait for the scanning process to complete and then restart your computer. All corrupted files will be replaced on reboot.

Sometimes, the updating process fails due to missing or bad system files. That’s why the System File Checker scans for the corrupt or missing files and repairs them.

3. Run the DISM command

1. Press Windows key + X and run Command Prompt (Admin).
2. Copy and paste the following command on the command line: DISM.exe/Online /Cleanup-image /Restorehealth
3. In case the DISM can’t obtain files online, try using your installation USB or DVD. Insert media and type following command: DISM.exe/Online /Cleanup-Image /RestoreHealth /Source:/C:\RepairSource\Windows /LimitAccess
4. Be sure to replace the C:\RepairSource\Windows path of your DVD or USB .

Just like the SFC scan, DISM (Deployment Image & Servicing Management) is also a tool for dealing with various system errors, although more advanced errors. Therefore, if the SFC scan didn’t get the job done, your chances are better with DISM.

4. Run the Windows Update troubleshooter

If you’re running a newer version of Windows 10 or the Windows 10 Creators Update, you can definitely use the Windows Update troubleshooting tool. This tool is suitable for fixing several system-related issues most especially Windows Update problems.

Meanwhile, if you’re not sure how to use the new troubleshooter in Windows 10, just follow the instructions below:

1. Go to Settings
2. Head over to Update & Security, then Troubleshoot.
3. Go to the Additional troubleshooter option.
4. Find Windows Update, and click Run the troubleshooter.
   
5. Follow further on-screen instructions.
6. Restart your computer.

5. Run System Restore in Safe Mode

1. In the search bar, type system restore.
2. The PC will prompt you to choose a restore point. Open the menu and, in the System Protection tab, click on System Restore.
3. Choose one of the available dates.
4. Follow the prompts to revert back to a certain restore point.
5. Wait for the process to complete, and then reboot.

Safe Mode is a diagnostics mode in Windows that starts your PC in a limited state, with only basic files and drivers running.

However, you can perform a system restore in safe mode to revert back to a certain restore point before the Your PC will restart several times error problem.

Note: Make sure you are able to identify the restore point before the error message display. Also, System restore does not affect any of your files, documents, and personal data.

6. Reset the PC

1. Open Settings, then Update & Security and go to Recovery.
2. The Reset this PC option should be the first you see. Click on Get started to proceed.

This option is an advanced recovery option that restores your PC to its factory state.

In a similar manner, but running in Safe Mode you should also be able to revert to a previous version of Windows. An intact Windows.old file (stored in C:\Windows.old ) is the important precondition for the downgrade.

7. Reset Windows Updates components

Disclaimer: This solution contains steps that are part of modifying the registry. Please note that serious problems may occur if you do this incorrectly. Hence, follow these steps correctly, and carefully.

We highly recommend that you back up the Registry before you modify it. Also, you can restore your PC to a working state in case a problem occurs.

Here’s how to manually reset the Windows Updates Components:

1. Right-click Start.
2. Select Command Prompt (Admin).
3. Click Yes when asked for permissions.
4. Stop the BITS, Cryptographic, MSI Installer, and Windows Update Services by typing the following commands in command prompt (hit Enter after each command you type):

• net stop wuauserv
• net stop cryptSvc
• net stop bits
• net stop msiserver

1. Rename the SoftwareDistribution and Catroot2 folder by typing the commands below in the Command Prompt then press Enter after each command you type:

• C:\Windows/softwareDistribution/SoftwareDistribution.old
• C:\Windows/System32/catroot2/Catroot2.old

1. Restart the BITS, Cryptographic, MSI Installer, and Windows Update Services by typing the following commands in Command prompt:

• net stop wuauserv
• net stop cryptSvc
• net stop bits
• net stop msiserver

1. Type Exit in the Command Prompt to close it.

After trying out the steps above run Windows Updates again and follow the prompts to complete Windows Update process.

However, some Windows users reported getting Access Denied prompts when trying the step above. Here’s what to do if your access is denied:

1. Log in first as administrator or use administrator user account
2. Stop the Windows Update service and try to rename Software Distribution folder
3. Right-click on Start.
4. Select Run.
5. Type services.msc and press OK or enter.
6. Scroll down and locate Windows Update service.
7. Right-click and select Properties.
8. Stop the service.
9. Follow the steps again to reset Windows Update Components.

After you complete the process, go to Services window again, now start Windows Update service, and then restart the computer.

Note: We highly recommend that you check the Give me updates menu for other Microsoft products when using Windows update option. Windows Updates downloads and installs updates required to run Windows efficiently.

Let us know if any of these solutions helped fix Your PC will restart several times problem.

FAQ: Learn more about Windows 10 updating errors

Since there might be several reasons why your PC got stuck while updating, you should try a few basic troubleshooting steps that work in most similar situations.

• How long should Windows update take?

If the updating process runs smoothly and doesn’t get stuck or something similar, it takes from several minutes to some 20-30 minutes, depending on the updates.

• What to do if your laptop is stuck on restarting?

If your laptop is stuck on restarting after an update, try booting in Safe Mode and install updates there.

Editor’s Note: This article was originally published in June 2018 and was revamped and updated in July 2020 for freshness, accuracy, and comprehensiveness.

Источник