Windows failed to load because a required file is missing or corrupt

Windows failed to load because a required file is missing or corrupt. File: acpi.sys Status: Oxc0000098

Do you know when this problem began? Try a System Restore to a point in timeBEFORE the problem began. Here’s the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/ . Be sure to check the box to show more than 5 days of restore points. If the first attempt fails, then try an earlier point or two. NOTE: You will have to re-install any software and updates you installed between now and the restore point, but you can use Windows Update for the updates. Use the recovery disk if the system prompt doesn’t work. The recovery disk works a bit different from the above procedures but if you follow the prompts from the System Restore menu option with the above information you should be able to restore with no problems.

If the System Restore doesn’t work, do a Startup Repair by booting to the genuine Windows Vista Installation Disk (or one you can borrow from ANYONE) or from a Recovery Disk. Here’s the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html . To boot to the CD you may need to change the BIOS to make the CD-drive first in the boot sequence. To do that, wait for the screen that tells you the F key to push to access the boot menu or boot setup. Push it quickly. Make the changes, save your work, and exit. Put the CD in the drive and reboot. When prompted, push any key to boot from the CD.

If you don’t have either disk, you can make a bootable Recovery Disk using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ along with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

If that doesn’t work, try to boot into safe mode (repeatedly click the F8 key while booting and go to safe mode with networking – or do so from the command prompt on the disk). Then let’s check some of your system files:

Go to Start / All Programs / Accessories / Command prompt and right click on command prompt and click run as Administrator (you can skip this step if using the disk).

If using the disk, cd to C:\Windows\System32. Type sfc /scannow and enter and let it run. It will scan and try to fix some of your system files. Hopefully it will complete with no corruption it could not repair (if there is such corruption post back here or try to analyze it to find the problem file(s) using http://support.microsoft.com/kb/928228 . Try to post any corrupted files here so we can see if they can be repaired with good copies from the installation disk (unless there are too many).

While in Command Prompt, type chkdsk /f /r and enter and let it run. It will want to schedule itself to run at the next restart. Answer yes and then reboot to run the program. It will scan and try to fix any corruption or bad sectors on your hard drive and mostly remove that as a potential cause.

If that doesn’t work, then please post any repeating error messages from the Event Viewer concerning startup (Start / Control Panel / Administrative Tools / Event Viewer – or typing eventvwr from the command prompt starting from C:\Windows\System32). Here’s how to use Event Viewer: http://www.petri.co.il/vista-event-viewer.htm . Look in the System section.

If this is a boot file problem, proceed as follows:

· To run the Bootrec.exe tool, you must start Windows RE. To do this, follow these steps: (you need a Vista Installation Disk to do this)

1. Put the Windows Vista installation disc in the disc drive, and then start the computer.

2. Press a key when you are prompted.

3. Select a language, a time, a currency, a keyboard or an input method, and then clickNext.

4. ClickRepair your computer.

5. Click the operating system that you want to repair, and then clickNext.

6. In theSystem Recovery Options dialog box, click Command Prompt.

7. TypeBootrec.exe, and then press ENTER.

Note If rebuilding the BCD does not resolve the startup issue, you can export and delete the BCD, and then run this option again. By doing this, you make sure that the BCD is completely rebuilt. To do this, type the following commands at the Windows RE command prompt:

· bcdedit /export C:\BCD_Backup

· ren c:\boot\bcd bcd.old

If you don’t have the disk, try EasyBCD http://neosmart.net/dl.php?id=1 and see if that helps resolve the problem.

Good luck and I hope this helps!

Lorien — MCSE/MCSA/Network+/A+ — If this post helps to resolve your issue, please click the «Mark as Answer» or «Helpful» button at the top of this message. By marking a post as Answered, or Helpful you help others find the answer faster.

Источник

Не могу установить Windows 7

Купил новый системник Acer M1930. Жеский диск пустой, поэтому пал выбор на установку Windows 7. Попросил друга скачать ОСь и проверить. Залили как загрузочный, все отлично. При мне установил у себя, все нормально. Вставляю в новый системник — ошибка! Долго мучался и в итоге поставил XP, но через пару дней форматнул жеский. Пробую установить снова Семерку — ни в какую. Сначала выдавало такое:

windows failed to start
a recent hardware or software change might be the cause to fix the problem:

1. insert your windows installation disc and restart computer.
2. choose your language setting, and then click «Next».
3. click «repair your computer».

if you have this disc, contact your system administrator or computer
manufacture for assistance.

file: \windows\system32\ четотам

info — windows failed to load because the kernel missing, or corrupt.

Помогите решить проблему.

Перевод можно не кидать!

Без вас шнур и mak592 я и сам перевел!

Мне нужна реальная помощь, а не дурацкие советы вроде этих!

окна не удалось запустить
последние аппаратные или программные изменения могут быть причиной, чтобы решить эту проблему:
1. вставить окна установочный диск и перезагрузите компьютер.
2. выбрать язык установки и нажмите кнопку «Далее».
3. нажмите кнопку «Восстановить компьютер».
если у вас есть этот диск, обратитесь к администратору системы или компьютера
производства для получения помощи.
Файл: \ Windows \ System32 \ четотам
Статус: 0xc0000098
Информация — окна не удалось загрузить, потому что ядро ​​отсутствует или поврежден

Все вышенаписанные «рекомендации» — чушь! Я смог решить такую проблему лишь воспользовавшись советом дельного пользователя с одного из пк-форумов:
«Эта ошибка возникает чаще всего из-за конфликта IDE устройств, а именно жесткого диска и привода! (особенно если они подключены к одному шлейфу).
Просто создай загрузочную флешку, отключи привод (полностью) и попробуй загрузиться с нее. Например у меня все прокатило. ) «

Благо, на моём ПК 2 привода; воткнул во второй — помогло. Думаю, что проканало бы и использование внешнего usb-привода.

Источник